PVC Conical Twin Screw Pelletizing Line
A conical twin screw pelletizing line for rigid and soft PVC that converts regrind, profiles and pipes into uniform pellets at controlled temperature.
RAL 5021 · semi-matt finish
Production line introduction
How the PVC Conical Twin Screw Pelletizing Line is engineered, and which sub-assemblies protect the properties your customers actually buy.
A conical twin screw pelletizing line for rigid and soft PVC that converts regrind, profiles and pipes into uniform pellets at controlled temperature.
Every BENK line is matched to the material and product you actually sell. The extruder, die, calibration or forming section and the downstream automation are sized together, then assembled and trial run in our Zhangjiagang works before shipment, so the performance you see in the factory acceptance test is the performance you install. The machine frame is finished in RAL 5021 water blue with a semi-matt powder coating.
Technical Parameters of PVC Conical Twin Screw Pelletizing Line
Reference values for the standard configuration. Final width, thickness, speed and output are confirmed against your material, product drawing and target capacity.
| Item | Specification |
|---|---|
| Material | Rigid and soft PVC |
| Extruder | SJZ 51/105 to 80/156 conical twin screw |
| Output | 150 – 800 kg/h |
| Pelletizer | Hot die face or strand pelletizer |
| Additives | Automatic dosing of stabilizer and filler |
| Control | PLC with temperature profiling |
Need a model outside this table? Send us your sheet size, resin and target output — BENK will return a sized configuration with a budgetary price.
Production line technical advantages
Every sub-assembly below is selected to protect the properties your customers buy: transparency, gauge, strength and surface.
Conical twin screw
Low shear high output mixing gives uniform plasticization and is gentle on heat sensitive PVC.
Production line advantages
- Conical twin screw — Low shear high output mixing gives uniform plasticization and is gentle on heat sensitive PVC.
Built to run
Material preparation, feeding, downstream handling and packing can be integrated into one turnkey scope.
Process flow
From raw material to finished pack, each station is matched in capacity so the line runs at the rated output without a bottleneck.
- Material preparation
- Extrusion & filtration
- Melt pump
- Die & forming
- Calibration / cooling
- Haul-off
- Cutting
- Stacking & packing
Wide applicability
Typical end uses for the material this line produces, based on the applications BENK equipment already serves worldwide.
Vacuum degassing
Volatiles and moisture are removed so the pellet is free of bubbles and porosity.
Options and auxiliary equipment
Configure the line for the market you sell into. Popular additions include:
- Automatic stacking and packing
- Online thickness or weight measurement
- Co-extrusion for functional surface layer
- Trim and scrap recycling
- Upgraded PLC with recipe management
- Remote maintenance and fault diagnosis
Why buy from BENK Machinery
Extrusion specialists, not traders
BENK designs and builds extrusion lines in Zhangjiagang with an in-house R&D and process team, so machine selection is matched to your resin and product instead of a catalogue number.
Evidence before shipment
Every line is assembled and run in our works. You receive trial video, gauge and output records, and are welcome to attend the factory acceptance test.
Total cost, not lowest price
Energy-efficient drives, permanent magnet motors and optimized heating reduce kWh per tonne, which usually matters more over five years than the initial purchase price.
Real commissioning support
Our engineers install, commission, train your operators and stay involved until the line hits the specified output and quality on your material.
Spares and response
Critical spares are stocked for fast dispatch, and the Siemens Ethernet control platform allows remote diagnosis before a service visit is needed.
Upgrades as you grow
Co-extrusion, gauge control, automation and downstream equipment can be added later, protecting your original investment.
Frequently asked questions
The questions buyers ask most often about this pvc pelletizing.
Automatic dosing
Get a quotation for the PVC Conical Twin Screw Pelletizing Line
Tell us the material, sheet or film size, target output and the country the line will be installed in. We will reply with a sized configuration, a budgetary price and an indicative delivery time.
- Telephone
- +86 512 5896 1463
- Mobile / WhatsApp / WeChat
- +86 159 5096 2426
- kpm@benkpm.com
- Address
- No.20 Huatang Road, Economic Development Zone (South District), Zhangjiagang City, Jiangsu Province, China
Related extrusion lines
Zhangjiagang City BENK Machinery Co., Ltd. · www.benkpm.com · Plastic extrusion lines and extruders since 2004.